top of page

Nobody Wants to Deburr: How Our 7-Axis OB7 Cobot Automates Deburring

7 days ago
3 min read
Nobody wants to deburr. Let OB7 do it.

Deburring is the job everybody in the shop hates. It's slow, it's dusty, and every part off your CNC machines still needs it before it ships.


Our 7-axis OB7 cobot takes it over. It picks up the part, runs every edge against your bench grinder with the same force every time, and sets it down. Then it grabs the next one.



WHY IT MATTERS

Same finish, every part, every shift


Deburring is easy to describe and hard to staff. It's repetitive, physically demanding work with high turnover, and the finish depends on who is at the grinder and how far into the shift they are.


MANUAL DEBURRING

An operator stands at the grinder for hours, breathing metal dust, and the pressure on each part drifts as the shift goes on.

OB7 DEBURRING

OB7 holds the same force on every edge, cycle after cycle. Your operator loads the grid and moves on to other work.



PROVEN ON OUR OWN FLOOR

OB7 deburrs our own gears


Gear deburring used to be our worst shop job. Now OB7 does it in our own factory in Carpinteria, California. Here is what changed compared to manual deburring:


10% → 1%

scrap rate

2x

throughput vs. manual deburring



HOW IT WORKS

Pick. Deburr. Place. Repeat.


OB7 picks a gear from the grid, deburrs it on the wheel and places it back

01


Pick

FROM THE GRID

OB7 reaches into the staging grid and grabs the next part.

02


Deburr

CONSTANT FORCE

It runs every edge against the wheel at the angles you taught it.

03


Place

BACK TO THE GRID

It sets the finished part down and reaches for the next one.


What makes it work:

  • One cycle takes 30 seconds to a few minutes, depending on the part

  • Stage 30, 40 or more parts and OB7 works through the whole batch on its own

  • OB7's 7th joint rotates ±540°, so it can spin round parts against the wheel for an even finish all the way around

  • The deburring stage holds a constant force, adjustable from 1.5 to 14.9 lb, and compensates up to 2" as the wheel wears

  • A regrip station lets OB7 set the part down, grab it again and finish the other side



NO PROGRAMMING

Teach it by hand


You move the arm through the motions once and OB7 remembers them. Productive Robotics was the first in the industry to introduce teach by demonstration. No code, no robotics engineer.


10 min

to teach a simple part

Minutes

to load a saved job when it comes back

5 parts

the smallest batches our customers run



TURNKEY SOLUTION

Open or enclosed, in one package


Everything ships as one package. Plug it into standard 110V power and 60 PSI shop air. No safety fencing, no special foundations and no IT setup.


OB7 open cell deburring package with the enclosed cell option

Every package includes:

  • 7-axis OB7 cobot arm, controller and tablet

  • PG2 parallel programmable electric gripper

  • Deburring stage with force control, mounts most common bench grinder motors

  • 47" × 47" work table and robot stand

  • Robot machine interface and all necessary cables


OPEN CELL

Fits where a workbench fits: a 47" × 47" footprint, about 16 sq ft. Half a day to unpack and set up.

ENCLOSED CELL

Everything in the open cell, plus an enclosure that keeps metal dust and debris inside the cell instead of in your shop.




FREE GUIDE

Deburring Automation with Cobots


Want the full picture? Our free guide gives machine shops straight answers on what cobot deburring takes, how teaching works and what it costs, with an ROI calculator to run your own numbers.




Want to see OB7 deburr your parts? Contact us to book a live online demo.



Comments


bottom of page